Spec glossary
Every label on a BASSBOSS product page, in plain words, with a real example from our line. Our figures are measured with all filters and limiters in place, and SPL is quoted at 1 meter half-space.
Also shown as: Type
A one-line description of what the cabinet is: how many ways, what size drivers, powered or not.
Read it left to right. "2-Way" means two drivers handle different parts of the range. "Single 12″" or "Quad 21″" counts the main woofers. "Self-powered" means the amplifier is inside the cabinet. "Vented" and "direct-radiating" describe how the woofer is loaded.
ExampleKraken-MK3: Quad 21″ self-powered subwoofer.
Also shown as: Frequency Range, LF
The range of low-to-high frequencies the speaker plays, with the level held within ±3 dB.
Every BASSBOSS figure is quoted at ±3 dB, so the edges of the range are where the output has dropped by 3 dB, not where sound stops entirely. The first number is the low limit, which is what a sub buyer cares about most (the compare tool calls it LF). Our numbers have no marketing EQ. Compare the low number first, then check that the range overlaps with the speaker you pair it with.
ExampleKraken-MK3: 27–100 Hz (±3 dB).
How low the response reaches when two cabinets run together.
Two subs sitting together couple and reinforce each other at low frequencies, so a pair reaches lower than one box. This line gives that lower limit at ±3 dB. It is a pair figure, so do not compare it to the single-cabinet Frequency Response of another product.
ExampleZV28-MK3: 21 Hz in a pair.
Also shown as: Max SPL
The loudest level the speaker holds, in dB SPL, measured 1 meter away with the cabinet on the ground.
SPL is sound pressure level. Our figures are quoted "@ 1m half-space": measured at 1 meter with the cabinet on the ground, which is how a sub works in a real room. We measure Maximum Output with all filters and limiters in place, so you get the number the product delivers as shipped. Output scales predictably: +6 dB per doubling. Half-space measurement, real-world coupled response. Compare half-space figures to half-space figures only.
ExampleKraken-MK3: 145 dB @ 1m half-space.
The short-burst ceiling: higher than Max Sustained SPL because it counts brief peaks, not a held level.
Peak and Max Sustained are two different numbers and they are not interchangeable. Peak covers short bursts such as a kick drum hit. Max Sustained is the level the speaker can hold. When you compare brands, make sure you are comparing the same kind of number. Most BASSBOSS products list both so you can see the gap.
ExampleKraken-MK3: 148 dB peak next to 145 dB max sustained.
The combined level of a multi-cabinet system, not a single box.
Used where a product is several cabinets working together. A plus sign means at least that level. Sound drops with the inverse square law, so what you hear depends on how far you stand from the stack.
ExampleStackatoa: 145+ dB combined.
The angle of coverage, horizontal × vertical, where the sound stays even.
A top listed at 90° × 60° covers 90 degrees side to side and 60 degrees up and down. Wider angles reach more of the room. Narrower angles throw further and keep sound off walls. "Rotatable" means the horn can be turned to swap the two angles. For subs, 360° means the cabinet radiates in all directions, and Cardioid mode (built into the DSP) lets a group of cabinets pull output away from the rear.
ExampleMFLA-MK3: 120° Horizontal · Array-dependent Vertical.
Also shown as: Transducer, DRV
The drivers inside the cabinet: how many, what size, and what they are made of.
A transducer turns the amplifier signal into sound. Subs list the woofers and their voice coils. Neodymium magnets are lighter than ferrite. Tops list each driver by the part of the range it plays: LF, MF, MLF and HF, explained below.
ExampleKraken-MK3: 4 × 21″ (540mm) neodymium · 4.5″ voice coils · 6th-order hybrid.
Also shown as: LF Drivers
The low-frequency driver or drivers: the woofers.
LF drivers do the heavy lifting in the bass. The listing gives the count, cone size, magnet type, voice coil size and any cone treatment. More cone area moves more air, which is why bigger and more drivers go lower and louder.
ExampleKrakatoa: 4 × 18″ (450mm) neodymium woofers · 4″ voice coils · waterproof cones.
Also shown as: MF Drivers
The midrange driver, covering the voice and the body of instruments.
Three-way and larger systems add a driver dedicated to the midrange so the woofers and the horn do not have to stretch into it. This is the range where vocals live.
ExampleAT312-MK3: 12″ (300mm) neodymium midrange driver · 3.5″ (88mm) voice coil.
The mid-low driver, a mid-bass driver bridging the woofers and the midrange.
Only the largest full-range systems carry one. It handles the region between the woofers and the midrange.
ExampleKrakatoa: 18″ (450mm) neodymium mid-bass driver · 4″ voice coil.
Also shown as: HF Drivers
The high-frequency driver: the compression driver and horn that carry detail and air.
A compression driver is a small diaphragm fed into a horn or waveguide. The listing gives the diaphragm size, the throat or exit size and the horn shape, which sets the Dispersion.
ExampleMFLA-MK3: 2 × 3″ (76mm) diaphragm compression drivers · 1.4″ (35mm) exits · isophasic wave guides.
The frequency where the sound hands off from one driver to the next.
Below it the woofer plays. Above it the horn takes over. The DSP does this split and keeps the two drivers in step with each other, so you do not need an outboard crossover.
ExampleAttuned12: 800 Hz.
Also shown as: Amplification, Total Amplification, AMP, LF Amplifier, MF Amplifier, MLF Amplifier, HF Amplifier
The built-in Class D amplifier, listed in watts, sometimes split by channel or driver.
Every BASSBOSS cabinet has its amplifier inside, so the watts you read are the watts driving that cabinet. "Total" adds every channel together. "LF", "MF", "MLF" and "HF" amplifier lines show how much power goes to each driver. Watts are a poor way to rank loudspeakers. Use them to see how much headroom a driver has, and use SPL to compare loudness.
ExampleKraken-MK3: 10,000W Class D (4 × 2500W).
The mains voltage the cabinet accepts.
"Auto-sensing" means the supply adjusts to whatever it is plugged into inside the range, so the same cabinet works on US and international power with no switch.
ExampleKraken-MK3: 100–240V AC, 50–60 Hz (auto-sensing).
Also shown as: Current @ 120V, Current @ 240V
How much current the cabinet pulls from the wall, at 120V and at 240V.
Use it to plan circuits. Add up the draw of every cabinet on a breaker and stay under that breaker's rating. "Nominal" is the typical running draw. The same cabinet draws roughly half the current at 240V as at 120V.
ExampleKraken-MK3: 18A @ 120V / 9.2A @ 240V.
The power inlet on the cabinet, with its connector type and rated capacity.
BASSBOSS cabinets use Neutrik powerCON True 1 TOP connectors, IP65-rated. The capacity figure is the most the inlet can carry, which matters when you link cabinets together.
ExampleKraken-MK3: Neutrik powerCON True 1 TOP (IP65).
Also shown as: Lighting Power Out
A power outlet on the cabinet that lets you link the next one, with its maximum capacity.
The outlet passes mains power on, so one cable run can feed several cabinets. Stay inside the capacity shown, and count the linked cabinets in your Current Draw. Some products add a pass-through outlet for a top-mounted light.
ExampleAT312-MK3: Neutrik powerCON True 1 female · outlet capacity 10A / 1200W.
The plug on the end of the power cable that ships with the cabinet.
Shows the standard it ships with (NEMA 5-15 for the US). Some products note that alternate connectors are provided outside the US.
ExampleKraken-MK3: NEMA 5-15 (Edison): 120V.
How the amplifier keeps its temperature in check.
Passive cooling uses a heat sink and the airflow the woofer already makes. Bigger products add fans that engage when the load calls for it. Thermal management is automatic.
ExampleKraken-MK3: Blower fans, auto thermal management.
The safeguards that keep the drivers and amplifier alive.
Limiters hold the signal below the point where the drivers or amp would be damaged, so night 400 sounds like night one. Thermal protection backs off the output if the amp gets too hot. Short-circuit and DC offset protection guard against faults at the outputs.
ExampleKraken-MK3: Multi-stage limiting, thermal, short-circuit, DC offset.
Also shown as: Processing
The onboard digital signal processor: crossover, limiting and the voicing built into the cabinet.
DSP stands for digital signal processing. BASSBOSS cabinets run it onboard at 96 kHz sampling. The line also shows how many presets are stored in the cabinet.
ExampleKraken-MK3: 96 kHz · 21 onboard presets · up to 100 via ControlBASS.
Also shown as: Total Preset Storage
The presets stored in the cabinet, and how many it can hold in total.
Presets are saved settings you recall from the cabinet or from ControlBASS. Onboard presets ship loaded. Total storage is the full number you can keep, up to 100. Some presets are high-pass filters (Linkwitz-Riley or Butterworth) with the cutoff in the name. The presets guide shows each curve.
ExampleAttuned12: 100 presets via ControlBASS / LAN.
The software you use to adjust the cabinet's DSP.
ControlBASS is the free app for macOS and Windows. It lets an engineer change gain, EQ and delay for every cabinet from one screen.
ExampleKraken-MK3: ControlBASS software (macOS / Windows).
The lights on the cabinet that show its state.
They show power and signal, how close the signal is to the limiter, and whether thermal or protection circuits have engaged.
ExampleAttuned12: Power/Ready · Signal · −12 dB · −6 dB · Limiter · Thermal · Protect · LAN · 8 preset LEDs.
The recommended preset for each cabinet when the three Stackatoa cabinets run as one system.
The three cabinets each need a matching preset so they act as one point-source system. The line says which one to start with and reminds you to check the combined system on site.
ExampleStackatoa: Kraken on Stack 20-65LR, Makara on preset 1.
Where the audio comes in.
A balanced XLR input. Balanced means long cable runs stay quiet.
ExampleKraken-MK3: XLR-F balanced.
Also shown as: Signal I/O
A pass-through that sends the incoming audio on to the next cabinet.
"Pass-through" means the output carries the input signal unchanged, so you can daisy-chain cabinets without a splitter.
ExampleKraken-MK3: XLR-M balanced pass-through.
Also shown as: Network (×2)
The Ethernet ports for control, with the count in brackets.
Ethernet carries ControlBASS and LAN preset loading. Milan AVB networking puts every cabinet in a system on one screen over a single Ethernet run. The "×2" means two ports, so you can chain cabinets.
ExampleAT312-MK3: Ethernet: ControlBASS + LAN preset loading.
The longest network cable you can run before you need another segment.
Applies to the network connection, not audio or power. Stay within the figure per segment.
ExampleKraken-MK3: 100m per AVB segment.
Also shown as: Construction
How the cabinet is built: the wood, the joinery and how the woofer is loaded.
CNC-machined Birch plywood with dado joinery and bracing. The loading (vented, short-horn hybrid, direct-radiating) sets how the woofer produces bass.
ExampleKraken-MK3: Vented, short-horn hybrid: CNC-machined 18mm Baltic Birch plywood · dado joinery · extensive bracing.
The coating on the outside of the cabinet.
A high-pressure bonded polyurea coating, which is a tough, textured skin that stands up to knocks on the road. Colors are listed where there is a choice.
ExampleKraken-MK3: Polyurea coating: waterproof, impact-resistant, textured black.
The metal screen that covers the drivers.
Perforated, powder-coated steel. Some models add a cloth liner or backing.
ExampleCCM12-MK3: Perforated, powder-coated steel with hydrophobic cloth liner.
Also shown as: Dimensions (H×W×D), Dimensions (Transport), Dimensions (Assembled), Total Height, Floor Footprint
The cabinet size in height × width × depth.
Check whether feet or flyware are included: the listing says so. Some multi-section products give a transport size and an assembled size. Systems also list total height and the floor footprint.
ExampleKraken-MK3: 48″ × 48″ × 36″ (48.5″ high with feet).
What the cabinet weighs on its own.
Net weight is the cabinet without packaging. Plan the load-in and any rigging around this number.
ExampleKraken-MK3: 460 lbs (209 kg).
The weight of the cabinet as packed for delivery.
It is heavier than the Net Weight because it includes the packaging. Use it for freight and the dock.
ExampleAT312-MK3: 140 lbs (63.5 kg).
The count and type of handles on the cabinet.
Handles are listed by number and material so you can plan how many people it takes to move it.
ExampleKraken-MK3: 8 steel bar handles.
Also shown as: Sliders, Caster Mounts
What the cabinet sits and slides on.
Interlocking foot pockets and feet keep stacked cabinets lined up. Sliders let a heavy cabinet slide on a stage. Caster mounts are T-nuts for optional casters.
ExampleKraken-MK3: Interlocking foot pockets: stable multi-cabinet stacking.
The mounting points for hanging the cabinet.
M10 threaded points are where rigging hardware attaches. Optional hardware such as eye bolts is listed under Optional.
ExampleKraken-MK3: 16 × internally braced M10 threaded mounting points.
Also shown as: Pole Sockets, Pole Mount
The socket that lets a top sit on a pole over a sub.
A 35mm socket fits a standard speaker pole. The count and size are listed.
ExampleAT312-MK3: 1 × 35mm steel pole socket.
Also shown as: Optional Hardware, Optional Cover, Optional Cart
Extras you can add to the cabinet. They are not included.
Rigging hardware, transport covers and carts are listed under Optional. They ship separately.
ExampleKrakatoa: Birch plywood flat cart with 4 locking wheels: transports 1 or 2 cabinets.
What comes in the box with the cabinet.
Anything not listed here, such as covers and rigging hardware, is sold separately.
ExampleAT312-MK3: Loudspeaker · 15' (5m) Power Cable · Manual · Warranty Card.
Also shown as: Sections
The cabinets or sections that make up a multi-part product.
Stackatoa lists the three cabinets that form it. Sublim8 lists its sections.
ExampleStackatoa: 1× Krakatoa · 1× Makara · 1× Kraken.
A recognition the product has earned, listed with its source.
Shown on the spec table so it travels with the product.
ExampleStackatoa: Best in Show: NAMM 2026 (ecoustics.com).
| Product | Frequency Response | Max Sustained SPL | Peak SPL | Amplifier | Net Weight |
|---|---|---|---|---|---|
| BB15-MK3 | 40–115 Hz (±3 dB) | 127 dB @ 1m half-space | 130 dB | 2500W Class D | 72 lbs (32 kg) |
| DJ18S-MK3 | 27–100 Hz (±3 dB) | 129 dB @ 1m half-space | 132 dB | 2500W Class D | 110 lbs (50 kg) |
| SSP118-MK3 | 30–100 Hz (±3 dB) | 130 dB @ 1m half-space | 133 dB | 2500W Class D | 125 lbs (57 kg) |
| VS21-MK3 | 28-100 Hz (±3 dB) | 135 dB SPL @ 1m half-space | 138 dB SPL @ 1m half-space | 2500W Class D | 180 lbs (82 kg) |
| SSP215-MK3 | 35–100 Hz (±3 dB) | 133 dB @ 1m half-space | 136 dB | 5000W Class D (2 × 2500W) | 180 lbs (82 kg) |
| SSP218-MK3 | 30–100 Hz (±3 dB) | 136 dB @ 1m half-space | 139 dB | 5000W Class D (2 × 2500W) | 199 lbs (90 kg) |
| ZV28-MK3 | 23–90 Hz (±3 dB) | 134 dB SPL @ 1m half-space | 137 dB SPL @ 1m half-space | 5000W Class D (2 × 2500W) | 235 lbs (106.5 kg) |
| Makara-MK3 | 23–100 Hz (±3 dB) | 140 dB @ 1m half-space | 143 dB | 5000W Class D (2 × 2500W) | 294 lbs (133 kg) |
| Kraken-MK3 | 27–100 Hz (±3 dB) | 145 dB @ 1m half-space | 148 dB | 10,000W Class D (4 × 2500W) | 460 lbs (209 kg) |
| SV9-MK3 | 50–19,000 Hz (±3 dB) | 118 dB @ 1m half-space | 121 dB @ 1m half-space | 1,200W Class D (2-channel) | 27.5 lbs (12.8 kg) |
| CCM12-MK3 | 50–19,000 Hz (±3 dB) | 123 dB @ 1m half-space | 126 dB @ 1m half-space | 1,200W Class D (2-channel) | 30 lbs (13.5 kg) |
| DiaMon-MK3 | 50–19,000 Hz (±3 dB) | 123 dB @ 1m half-space | 126 dB @ 1m half-space (limited in full-range) | 1,200W Class D (2-channel) | 30 lbs (13.5 kg) |
| DV12-MK3 | 45–19,000 Hz (±3 dB) | 128 dB @ 1m half-space | 134 dB @ 1m half-space | 3,200W Class D (2400W LF + 800W HF) | 63 lbs (28 kg) |
| Attuned12 | 65–19,000 Hz (±3 dB) | 130 dB SPL @ 1m full-space | 136 dB SPL @ 1m full-space | 3,200W Class D, 2-channel | 55 lbs (24.95 kg) |
| AT212-MK3 | 50–18,000 Hz (±3 dB) | 136 dB SPL @ 1m half-space | 142 dB SPL @ 1m half-space | 3,200W Class D, 2-channel | 99 lbs (45 kg) |
| AT312-MK3 | 60–19,000 Hz (±3 dB) | 133 dB SPL @ 1m half-space | 139 dB SPL @ 1m half-space | 4,000W Class D, 3-channel | 126 lbs (57 kg) |
| MFLA-MK3 | 60–18,000 Hz (±3 dB) | 136 dB SPL @ 1m half-space | 142 dB SPL @ 1m half-space | 3,200W Class D, 2-channel | 104 lbs (47 kg) |
| Sublim8 | 35–19,000 Hz (±3 dB) | 132 dB (half-space) | 135 dB (half-space) | 4,000W Class D | 200 lbs (90.7 kg) |
| Krakatoa | 25–19,000 Hz (±3 dB) | 142 dB @ 1m half-space | 145 dB @ 1m half-space | 7,500W Class D | 470 lbs (213 kg) |
| Stackatoa | 25–19,000 Hz (±3 dB) | 145+ dB combined | n/a | 22,500W Class D (combined) | 470 lbs (213 kg) |